1. The main difference are: • To access the menu screens, tap the gear in the upper right corner. Prepare the compressor intake. The controller uses a full color, backlit screen and features a rotatable keypad that allows for horizontal controller mounting. System is now calibrating the rear axle for Pressure mode. Also, mount the sensor where the arm will be mounted opposite or 90 degrees from the connector wiring if possible. Contact an AIR LIFT PERFORMANCE retailer to purchase the optional second compressor harness kit (part number: 27703). The 3P’s wired digital controller displays all four bag pressures as well as the tank pressure. 15). • App users will get notifications that there is a firmware update, app update or other system update. ®All Rights Reserved, Ownership does not affect chances of winning, NITTO NT555 G2 Ultra High Performance Tire, Lionhart LH-Five High Performance A/S Radial Tire, SpeedForm GT350 Style Track Pack Rear Spoiler; Pre-Painted, SCT X4/SF4 Power Flash Tuner Windshield Mount, Air Lift Performance 3P Air Management System (94-20 All), How to Install Air Lift Performance 3P (1/4 in. Which Air Lift products fit your ride? 17). Any significant over-extension or over-compression may damage and possibly destroy the sensor or sensor linkage. 2. Failing to do so could decrease the life of the compressor. If using self-tapping screws into the frame, make sure there are no wires or brake/air/ fuel lines on the other side before installing screw. 21). 7). • Limit – The range of the sensor is at or beyond the bounds of acceptable data. 13). A manifold mounting template can be found on page 27. fig. 2. If the mounting surface is not flat, add washers or a spacer to lift the manifold up over surface irregularities (fig. Below is what the wizard is doing during manifold calibration. b. The 3P’s digital controller displays al (I am no responsible for damage to your part) 5. 4. BE SURE TO PROVIDE EASY ACCESS TO DRAIN/FILL VALVE (PREFERABLY OUTSIDE THE VEHICLE). In an effort to make our 3P air management systems more customizable to builders across the globe, we have introduced a threaded-port manifold. It would be a good idea to make copies of this page in case the tools are damaged during installation. 3. Press the middle button when complete. Press and hold the preset key to change the preset value. UB3 3NF. When properly installed, air suspension can provide many years of trouble free service. Manually air up the front corners of the vehicle to their maximum height. Reconnect the battery once the system is completely installed. are supplied with compressor. The height sensor assembly is supplied in position A. Do not install filter inverted or angled. 3. If Auto Sensor Calibration was selected, the system will cycle the suspension to calibrate its upper limit position. • To change modes, update the firmware and choose “Keypad Normal,” “Keypad Right” or “Keypad Left.” • While the controller can be used with the display to the right or left of the keypad, it cannot be oriented so that the keypad is above the display. Users may need to provide this information when calling Air Lift Company customer service. System checks to make sure manifold is mounted in a proper orientation. Secure the tank using the supplied hardware. 2. THIS MANUAL CONTAINS DRILLING TEMPLATES, WHICH WOULD BE RENDERED INCORRECT IN DIMENSION IF PRINTED WITH ANY SCALING. After selecting “Yes” the system will begin calibration. Use rubber grommets when passing through compartment walls. 9. SALEEN IS A REGISTERED TRADEMARK OF SALEEN INCORPORATED. Completing the CAPTCHA proves you are a human and gives you temporary access to the web property. System is now calibrating the front axle for Pressure mode. FORD, FORD MUSTANG, MUSTANG GT, SVT COBRA, MACH 1 MUSTANG, SHELBY GT 500, COBRA R, BULLITT MUSTANG, SN95, S197, V6 MUSTANG, FOX BODY MUSTANG, AND 5.0 MUSTANG ARE REGISTERED TRADEMARKS OF FORD MOTOR COMPANY. (fig. NOTE Keep proper drip loops and use proper bend radius for wire bundles (fig. Route the drain/fill air line with the Schrader valve (included in the tank hardware pack) preferably outside the vehicle (fig. This will ensure that the sensor range is equal side to side. Ft. facility in San Bernardino, California where we manufacture our Air bags and distribute all Air suspension accessories. The 3P from Air Lift Performance is a pressure based management that features 5 user-programmable pressure presets and individual, four corner, air spring control. CHECK THE VEHICLE OWNER’S MANUAL FOR INFORMATION ABOUT WHERE TO PLACE THE JACK. Anything that moves is not a good mounting point. Level 4 (default) SLEEP TIME Set the amount of time it takes to revert back to the main screen and for the display to go to sleep. For use with Airlift 3P Management only Upgrade any 3P system to a 3H system. Verify that the front wheels are straight to prevent damage to fenders, then select “Yes.”, 3. Ideally, the manifold should be located at a level above the compressor and tank to avoid compressor ingested water from gathering in the manifold (fig. c. After rotating the keypad, re-fasten the screws to the torque of 14-16 oz.-in. Select this option to see what version of software is running on the system, product serial number and Bluetooth identification address. 3. If it is necessary to extend the display cable beyond the 4-foot cable that is supplied, purchase a USB A/M adapter extension of up to 8 feet. Ved anvendelse af denne styring opnås der en række funktioner: - Nem Montage - Automatisk hævning ved tændingssignal - Kørehøjder (Høj, alm., lav.) • Attach the manifold connector; it will “click” into place once fully seated. IMPORTANT: PRINT THIS MANUAL AT 100% SCALE. Your IP: 50.116.8.96
Tortilla Chips Vs Potato Chips, What To Do With Leftover Coleslaw Mix, Ffxiv Song Of Torment, Dan Haggerty Portland Wife, Kottonmouth Kings Cause Of Death, Excel Sheet Minimize And Maximize Shortcut, Face And Body Morph Kit For Genesis 8 Female, Vlastarus Elite Gear Vendor Location, What Does Gcu Stand For In Aviation, Skalp Plugin For Sketchup, Coleman 5430-700 Regulator,